|
» »
EZ Web Lynx 3.3V
Add monitoring and control capability from any internet-ready mobile device or PC to your products. The module contains an integrated web server to bridge it's 17 I/O pins to any 10BASE-T Ethernet port. |
1-25: $49 26-99: $30 100-999: $22 More: RFQ
|
Adds monitoring and control capability to your products from any internet-ready mobile device or PC
- Provides access to data through any 10BASE-T port
- Serves custom HTML dynamic web pages for displaying data
- Sends email notifications of event driven alarms and/or daily status
Interfaces to analog and digital sensors, switches, relay drivers, motor drives and controls
- Any I/O pin can be used for digital I/O. 3.3V devices have 17 I/O pins. 5V devices have 11
- 6 I/O pins can be used as analog inputs on 3.3V devices; 5 pins on 5V devices. Analog inputs have a range from Vdd to GND and a resolution of (Vdd-GND)/256
- 2 I/O pins can communicate with Dallas sensors over an I2C bus to monitor temperature in Fahrenheit or Celsius
- 2 I/O pins can be used to implement a serial communications channel
- 5V devices also allow one pin to be configured as PWM; one as timer
- Configurable serial capture buffer allows EZ Web Lynx to automatically capture a specific frame of serial data based on user specified start and stop conditions
- 256 8-bit volatile and non-volatile registers are provided for data storage
Reduces development time and cost to get your products online
- Integrated web server bridges device I/O to Ethernet, reducing hardware and software development time
- Uses custom HTML tags to access and control all device I/O, PWM and timer channels, etc
- Serial AT command interface allows user to configure and operate the device without the need of a network connection
- UDP server interface included with EZ Web Lynx to accept AT commands and works with the EZ Web Lynx IDE to configure the device
- HTTP CGI interface commands can be issued to the EZ Web Lynx using HTTP CGI GET and POST commands
Easily integrated into networks
- EZ Web Lynx permits full modification of its networking settings, allowing it to be used in a variety of network environments
Device configuration protected from unauthorized modification
- Device Lock password protects EZ Web Lynx from changing the configuration of the device
- Pin Lock allows I/O pins to be individually locked in their current state to prevent mode configurations from being modified
General Specifications
Specification |
5.0V |
3.3V |
Physical Dimensions |
Width: 0.7" Length: 1.625" Height: 1.0" |
Width: 0.75" Length: 1.5" Height: 0.875" |
Header Size |
0.1 in |
2.0 mm |
I/O Pins |
11 - digital I/O pins total 9 - have additional features:
- 5 - analog
- 2 - serial communication
- 2 - I2C (Dallas DS1631
Temperature Sensors)
|
17 - digital I/O pins total 10 - have additional features:
- 6 - analog
- 2 - serial communication
- 2 - I2C (Dallas DS1631
Temperature Sensors)
|
Programming Method |
HTML for custom web content |
Supported Network Protocols |
HTTP |
- View HTML pages/send CGI |
UDP |
- Command interface, IP broadcasts |
SMTP |
- Email |
TFTP |
- Uploading/downloading HTML pages |
ICMP |
- (Ping) |
DHCP |
Ethernet Port |
10 Mbps Half Duplex (IEEE 802.3) |
Memory for HTML Pages |
927 KB |
896 KB |
|
Electrical Specifications
Specification |
5.0V |
3.3V |
Minimum |
Maximum |
Minimum |
Maximum |
Supply Voltage (Vdd) |
4.5 V |
5.5 V |
3.1 V |
3.6 V |
Supply Current1 |
175 mA @ 5.0 V |
N/A |
150 mA @ 3.3 V |
N/A |
Input Low Voltage (Digital)
Pin 1-7, 10, 11
Pin 8, 9
Reset2
Pin 1-6, 8, 9, Reset2
Pin 7, 10-17
|
GND GND GND |
0.8 V 0.2·Vdd 0.2 V |
GND
GND |
0.2·Vdd
0.8 V |
Input High Voltage (Digital)
Pin 1-7, 10, 11
Pin 8, 9
Pin 1-6, 8, 9
Pin 7, 10-17
|
2.0 V 0.8·Vdd |
Vdd Vdd |
1.7 V 0.8·Vdd |
Vdd Vdd |
Output Low Voltage (Digital) |
GND |
0.6 V |
GND |
0.4 V |
Output High Voltage (Digital) |
Vdd-0.7 V |
Vdd |
2.4 V |
Vdd |
Pin Current Source (Output)
Pin 1-7
Pin 8-17
|
|
25 mA |
|
2 mA 25 mA |
Pin Current Sink (Input)
Pin 1-7
Pin 8-17
|
|
25 mA |
|
2 mA 25 mA |
Board Layout
Documentation
Software
|